1. <rt id="addey"></rt>
    2. <ruby id="addey"></ruby>
      <rt id="addey"></rt>
        <rp id="addey"></rp>
        1. <b id="addey"><form id="addey"></form></b>
          <b id="addey"><form id="addey"></form></b>
        2. <rp id="addey"></rp>

        3. 歡迎來到山東途暢路橋工程有限公司官網!

          logo

          1. 專注強夯機租賃,液壓沖擊夯租賃、強夯工程施工碎石樁等
          2. 地基軟基處理于一體的高質量基礎工程施工公司

          全國施工租賃熱線

          18264104888

          強夯機是如何進行操作的?

          網址:http://www.xuanhuataobao.com/   發布日期:2020-08-04 關注次數:
          強夯機的操作流程是怎樣的呢,對此你有什么了解和看法嗎,我們這篇文章就為你解惑一下它到底是怎樣工作的呢?它總共有這11條,分別是:
          What do you think about the operation of the rammer? There are 11 items in total
          1)作為強夯作業的主要單位,應根據壓實度等級進行計算和選擇。以履帶式起重機為主機,實施履帶起重機的有關規定。
          1) As the main unit of dynamic compaction, it should be calculated and selected according to the degree of compaction. With crawler crane as main engine, relevant regulations of crawler crane shall be implemented.
          (2)搗固機工作區域應平穩,龍門架底座和搗固機地面應保持水平。當沉降超過100mm,框架的高度應再次提高。
          (2) The working area of tamping machine shall be stable, and the base of gantry frame and the ground of tamping machine shall be kept horizontal. When the settlement exceeds 100 mm, the height of the frame should be raised again.
          (3)對龍門框架、橫梁、脫鉤裝置的主要結構和構件的材料和制造質量進行嚴格檢查,不得按設計要求使用。
          (3) The materials and manufacturing quality of the main structures and components of the gantry frame, crossbeam and unhooking device shall be strictly inspected and shall not be used according to the design requirements.
          (4)在搗固機工作狀態下,吊桿應置于海平面70度以上。
          (4) When the tamping machine is working, the boom should be placed above 70 degrees of sea level.
          (5)的梯形門架腿不能錯位前、后支腿,并不能解除對墊錘。
          (5) The front and rear legs of the trapezoidal portal frame can not be dislocated, and the cushion hammer cannot be removed.
          強夯機出租
          (6)改變位置后,門腿應再次檢查確認的穩定性和可靠性,然后錘應解除100 ~ 300mm,整機的穩定性應進行檢查,下班后可以證實它是可靠的。
          (6) After changing the position, the door leg should be checked again to confirm the stability and reliability, and then the hammer should be removed by 100 ~ 300 mm. The stability of the whole machine should be checked, and it can be confirmed that it is reliable after work.
          (7)錘是向后的,在鉤頭降低到錘環之前,操作者不能鉤坑。當把錘子從坑里抬出來時,禁止把人鉤在錘子上,用錘子把它抬起來。
          (7) The hammer is backward and the operator cannot hook the pit before the hook head is lowered to the hammer ring. When the hammer is lifted out of the pit, it is forbidden to hook people on the hammer and lift it with a hammer.
          (8)當錘具有相應的排氣孔時,應隨時清洗。但嚴禁在錘下清洗。
          (8) When the hammer has corresponding vent hole, it should be cleaned at any time. However, cleaning under the hammer is strictly prohibited.
          (9)夯坑內有水或粘土時,應清除錘底力,不得吊錘。
          (9) When there is water or clay in the tamping pit, the bottom force of the hammer shall be removed and the hammer shall not be lifted.
          (10)通過輔助機械傳遞轉移搗固點的搗固點。從地面到腿的高度不得超過500mm的距離龍門和夯錘的作用。
          (10) The tamping point of tamping point is transferred by auxiliary mechanical transmission. The height from the ground to the leg shall not exceed 500mm from the gantry and rammer.
          (11)錘擊后,應放下并放在地上。嚴禁在非操作期內將錘子吊在空中。
          (11) After hammering, it should be put down and put on the ground. It is strictly forbidden to hang the hammer in the air during the non operation period.
          在使用強夯機前,你首先要對其進行安全檢測,首先要把安全放在首位,不能讓設備帶病工作,這是對生命的不負責任,對事情的不認真,所以,再做任何事情前要先擺好自己的態度!
          Before using the dynamic compaction machine, you should first carry out safety inspection on it. First of all, safety should be put in the first place, and the equipment should not work with diseases. This is irresponsible for life and not serious about things. Therefore, before doing anything again, you should put your attitude in place first!
        4. 標簽:
        5. 韩国A片在线观看全免费
            1. <rt id="addey"></rt>
            2. <ruby id="addey"></ruby>
              <rt id="addey"></rt>
                <rp id="addey"></rp>
                1. <b id="addey"><form id="addey"></form></b>
                  <b id="addey"><form id="addey"></form></b>
                2. <rp id="addey"></rp>